Kohler 4737-0 Instalační příručka

Procházejte online nebo si stáhněte Instalační příručka pro ne Kohler 4737-0. KOHLER 4737-0 Installation Guide Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 28
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 0
Installation Guide
Toilet Seat with Bidet Functionality
and Tank Water Heater
M product numbers are for Mexico (i.e. K-12345M)
Los números de productos seguidos de
M corresponden a México (e.j.
K-12345M)
Français, page “Français-1”
Español, pagina “Español-1”
K-4737
1097712-2-A
Zobrazit stránku 0
1 2 3 4 5 6 ... 27 28

Shrnutí obsahu

Strany 1 - Installation Guide

Installation GuideToilet Seat with Bidet Functionalityand Tank Water HeaterM product numbers are for Mexico (i.e. K-12345M)Los números de productos se

Strany 2 - Before You Begin

Avant de commencer (cont.)Respecter tous les codes électriques, de plomberie et de bâtimentlocaux.Connecter seulement l’alimentation d’eau en provenan

Strany 3

1. Préparer les connexions électriquesAVERTISSEMENT : Risque de choc électrique, d’incendie,de blessures. Ce produit doit être mis à la terre et doitu

Strany 4 - 2. Prepare the Toilet

Préparer les connexions électriques (cont.)AVIS : Ne pas brancher dans le siège avant l’instruction de le faire.Ceci permettra d’éviter un mauvais fon

Strany 5 - 3. Install the Mounting Plate

3. Installer la plaque de fixationREMARQUE : Inspecter les orifices de fixation des W.C. afin d’yrechercher des inserts filetés. Suivre les étapes applicab

Strany 6 - 4. Install the Seat

Installer la plaque de fixation (cont.)Faire passer chaque boulon par la plaque de fixation et dans lesorifices de fixation.Positionner les rondelles de m

Strany 7 - 5. Complete the Installation

4. Installer le siègePour toutes les installationsGlisser le siège dans la plaque de montage jusqu’à ce qu’elles’enclenche en place. Vérifier que le si

Strany 8 - 6. Installation Checkout

5. Terminer l’installationAVERTISSEMENT : Risque d’endommagement du matériel.Ne pas pousser sur le raccord d’eau entre le siège et la butéed’alimentat

Strany 9 - Guide d’installation

6. Vérification de l’installationAttacher les agrafes (fournies) de manière égale le long du tuyauet du cordon d’alimentation pour les arranger.Emballe

Strany 10

Guía de instalaciónAsiento de inodoro con funcionalidad de bidety calentador de tanque de aguaHerramientas y materialesAntes de comenzarADVERTENCIA: R

Strany 11

Antes de comenzar (cont.)Sólo conecte el suministro de agua del asiento al suministro deagua fría, supliendo agua potable y a una presión de 20-80 psi

Strany 12 - 2. Préparer les W.C

Tools and MaterialsBefore You BeginWARNING: Risk of electric shock, fire, or personal injury.This product must be grounded and connected only to adedic

Strany 13

1. Prepare las conexiones eléctricasADVERTENCIA: Riesgo de descarga eléctrica, incendio olesiones personales. Este producto tiene que conectarse atier

Strany 14

Prepare las conexiones eléctricas (cont.)AVISO: No enchufe el asiento hasta que se le indique. Esto evitarála posibilidad de malfuncionamiento del pro

Strany 15 - 4. Installer le siège

3. Instale la placa de montajeNOTA: Inspeccione los insertos roscados de los orificios de fijacióndel inodoro. Siga los pasos que apliquen a su tipo de

Strany 16 - 5. Terminer l’installation

Instale la placa de montaje (cont.)Inserte cada perno a través de la placa de montaje y dentro de losorificios de fijación.Coloque las arandelas de mane

Strany 17 - Plastique

4. Instale el asientoPara todas las instalacionesDeslice el asiento en la placa de montaje hasta que se sienta queencaja en su lugar. Verifique que el

Strany 18 - Guía de instalación

5. Termine la instalaciónADVERTENCIA: Riesgo de daños a la propiedad. Noempuje ni jale la conexión de agua entre el asiento y la llavede paso del sumi

Strany 19

6. Verificación de la instalaciónFije los clips (provistos) de manera pareja a lo largo de lamanguera y el cable eléctrico para organizarlos.Envuelva e

Strany 20

1097712-2-A

Strany 21 - 2. Prepare el inodoro

USA/Canada: 1-800-4KOHLERMéxico: 001-877-680-1310kohler.com©2009 Kohler Co.1097712-2-A

Strany 22

1. Prepare Electrical ConnectionsWARNING: Risk of electric shock, fire, or personal injury.This product must be grounded and connected only to adedicat

Strany 23

Prepare Electrical Connections (cont.)Preferred ConnectionDetermine the electrical outlet location. The electrical outletshould be located within 12″

Strany 24 - 4. Instale el asiento

3. Install the Mounting PlateNOTE: Inspect the toilet mounting holes for threaded inserts. Followthe steps applicable to your mounting hole type.For T

Strany 25 - 5. Termine la instalación

4. Install the SeatFor All InstallationsSlide the seat onto the mounting plate until you feel it snap intoplace. Verify the seat is properly aligned.N

Strany 26 - Envoltura de plástico

5. Complete the InstallationWARNING: Risk of property damage. Do not push or pullon the water connection between the seat and the watersupply stop. Th

Strany 27 - 1097712-2-A

6. Installation CheckoutAttach the clips (provided) evenly along the hose and power cordto organize them.Wrap the toilet seat with plastic wrap. This

Strany 28

Guide d’installationSiège de W.C. avec fonctionnalité de bidet etchauffe-eau de réservoirOutils et matérielsAvant de commencerAVERTISSEMENT : Risque d

Komentáře k této Příručce

Žádné komentáře